Publications
A wind forecast algorithm to support Wake Turbulence Mitigation for Departures (WTMD)
January 20, 2008
Conference Paper
Published in:
13th Conf. on Aviation, Range and Aerospace Meteorology, ARAM, 20-24 January 2008.
Topic:
R&D area:
R&D group:
Summary
Turbulence associated with wake vortices generated by arriving and departing aircraft poses a potential safety risk to other nearby aircraft, and as such this potential risk may apply to aircraft operating on Closely Spaced Parallel Runways (CSPRs). Aircraft separation standards are imposed to mitigate this potential risk. The FAA and NASA are investigating application of wind-dependent procedures for improved departure operations that would safely reduce spacing restrictions to allow increased airport operating capacity. These procedures are referred to collectively as Wake Turbulence Mitigation for Departures (WTMD). An important component of WTMD is a Wind Forecast Algorithm (WFA) developed by MIT Lincoln Laboratory. The algorithm is designed to predict when runway crosswind conditions will remain persistently favorable to preclude transport of aircraft departure wakes into the path of aircraft on parallel runways (Figure 1). The algorithm has two distinct components for predicting the winds at the surface (33 ft) and aloft up to 1000 ft (the altitude by which an alternate form of separation would be applied by Air Traffic Control to aircraft departing the parallel runways, typically 15 degree or greater divergence in aircraft paths). The surface component forecast applies a statistical approach using recent observations of winds from 1-minute ASOS observations. The winds-aloft component relies on the 2 to 4 hour wind forecasts from NCEP's Rapid Update Cycle (RUC) model. The baseline version of the algorithm was developed and tested using data from St. Louis Lambert International Airport (STL). Algorithm performance was evaluated using 1-minute ASOS observations and crosswind component measurements taken from a dedicated Light Detection and Ranging (LIDAR) system. The algorithm was also demonstrated and evaluated at Houston George Bush International Airport (IAH). Use of the WFA is planned for 8 other airports deemed likely to derive significant benefit from WTMD procedures. The operational concept of WTMD for use by Air Traffic Control (ATC) includes additional decision levels beyond the WFA forecast. These include a check for VFR ceiling and visibility conditions, and final enablement by a human controller. More details concerning WTMD can be found in Lang et al. (2005) and Lang et al. (2007). A more complete description of the WFA is given in Robasky and Clark (2008). The early history of WFA development is detailed in Cole and Winkler (2004).
Summary
Turbulence associated with wake vortices generated by arriving and departing aircraft poses a potential safety risk to other nearby aircraft, and as such this potential risk may apply to aircraft operating on Closely Spaced Parallel Runways (CSPRs). Aircraft separation standards are imposed to mitigate this potential risk. The FAA and...
READ MORE
Comparison of Rapid Update Cycle (RUC) model crosswinds with LIDAR crosswind measurements at St. Louis Lambert International Airport
January 20, 2008
Conference Paper
Published in:
13th Conf. on Aviation, Range and Aerospace Meteorology, ARAM, 20-24 January 2008.
Topic:
R&D area:
R&D group:
Summary
Turbulence associated with wake vortices generated by arriving and departing aircraft pose a potential safety risk to other nearby aircraft, and as such this potential risk may apply to aircraft operating on Closely Spaced Parallel Runways (CSPRs). To take wake vortex behavior into account, current aircraft departing/landing standards require a safe distance behind the wake generating aircraft at which operations can be conducted. The Federal Aviation Administration (FAA) and National Aeronautics and Space Administration (NASA) have initiated an improved wake avoidance solution, referred to as Wake Turbulence Mitigation for Departures (WTMD). The process is designed to safely increase runway capacity via actively monitoring wind conditions that impact wake behavior (Hallock, et al., 1998; Lang et al., 2005). An important component of WTMD is a Wind Forecast Algorithm (WFA) being developed by MIT Lincoln Laboratory (Cole & Winkler, 2004). The WFA predicts runway crosswinds from the surface up to a height of approximately ~300 m (1000 ft) once per minute and thus forecasts when winds favorable for WTMD will persist long enough for safe procedures for a particular runway (Lang et al., 2007). The algorithm uses 1–4 hr wind forecasts from the Rapid Update Cycle (RUC) model operated by the National Oceanic and Atmospheric Administration/National Centers for Environmental Prediction (NOAA/NCEP) for upper atmospheric wind profiles. Detailed description of the RUC model can be found elsewhere (Benjamin et al., 1994; 2004a; 2004b). Briefly, the RUC model inputs are assimilations of high frequency observations from a suite of meteorological sensors, including Automated Surface Observing System (ASOS), rawinsonde profiles, satellite, airborne sensors from commercial aircraft, etc. The vertical layers of the atmosphere are resolved approximately isentropically. The model is run hourly, producing hourly forecasts out to 24 hours. The coverage of the RUC grid includes the continental United States, southern Canada, northern Mexico, and adjacent coastal waters. Here we evaluate the performance of RUC in predicting crosswinds with reliability sufficient to support WTMD. For RUC validation, in situ wind profile data were obtained from a Light Imaging Detection and Ranging (LIDAR) deployed at St. Louis Lambert International Airport (STL). The focus of this study is to provide a general quantitative characterization of the difference between RUC predictions and LIDAR measurements of the runway crosswinds. Particular attention was given to cases with inaccurate RUC crosswind forecasts, and cases when significant horizontal and vertical shears occur during situations of convective weather or proximity to large scale weather features, e.g., air mass fronts. (In practice, WTMD procedures and existing weather sources in the Control Tower will manage, to an acceptable level of risk, the hazard exposure associated with the extreme wind shift examples presented here.) Also included was examination of performance degradation with longer RUC forecast horizons and coarser horizontal resolutions, which may be relevant with regard to actual operational forecast data availability, or future applications of the operational concept to include arrival operations. A detailed report for this study is also available (Huang et al., 2007).
Summary
Turbulence associated with wake vortices generated by arriving and departing aircraft pose a potential safety risk to other nearby aircraft, and as such this potential risk may apply to aircraft operating on Closely Spaced Parallel Runways (CSPRs). To take wake vortex behavior into account, current aircraft departing/landing standards require a...
READ MORE
Consolidated storm prediction for aviation (CoSPA)
January 20, 2008
Conference Paper
Published in:
Proc. of the 2008 Integrated Communications, Navigation and Surveillance Conf., 20-24 January 2008.
Topic:
R&D area:
R&D group:
Summary
Research over the last 10 years primarily funded by the FAA Aviation Weather Research Program (AWRP) has led to very successful development of forecasts of both convective and winter storms, using heuristic and numerical models, for aviation applications. We have reached a point where there are several overlapping capabilities, and the smorgasbord of choices has become confusing. Moreover, aviation-impacting winter and summer conditions can exist simultaneously - even within a single terminal area - so a consolidated forecast must work equally well for all storm conditions. Advances in computing and communications allow incorporation of new observing systems and scientific advancements in data assimilation and modeling toward large-scale, very high resolution forecast systems that were prohibitive just 10 years ago. Other government agencies, in addition to FAA, have needs for aviation-oriented forecasts, including at least the National Weather Service, NASA, Homeland Defense, Air Force and other DoD agencies. Further efficiencies will be realized by consolidating such efforts as well. These goals are well-aligned with the goals of the Next Generation Air Transportation System and its Joint Program and Development Office. The FAA Aviation Weather Research Program is leading development of the new Consolidated Storm Prediction for Aviation (CoSPA) effort, which will combine aviation-oriented storm research in a coordinated fashion, with the goal of eventually replacing operational legacy storm diagnostic and forecast products, as appropriate, that are also geared toward aviation (see Appendix A). While many of the current storm prediction products are derived using NOAA model forecast data, especially from the hourly updated 13-km Rapid Update Cycle (RUC) model over CONUS, CoSPA products will be related to a new generation of NOAA models now assimilating radar reflectivity and lightning, including the Rapid Refresh, its proposed nest - the High-Resolution Rapid Refresh (HRRR), and ensemble-based products from both. A kick-off meeting was held in June 2006 to discuss AWRP?s concepts for a consolidated aviation forecast, and to understand unmet user needs, major scientific development issues, and also to begin to explore issues associated with production and dissemination of a consolidated forecast. These findings are summarized below.
Summary
Research over the last 10 years primarily funded by the FAA Aviation Weather Research Program (AWRP) has led to very successful development of forecasts of both convective and winter storms, using heuristic and numerical models, for aviation applications. We have reached a point where there are several overlapping capabilities, and...
READ MORE
Evaluation of weather impact models in departure management decision support: operational performance of the Route Availability Planning Tool (RAPT) prototype
January 20, 2008
Conference Paper
Published in:
13th Conf. on Aviation, Range and Aerospace Meteorology, ARAM, 20-24 January 2008.
Topic:
R&D area:
R&D group:
Summary
In this paper, the revised RAPT algorithm and display are described and evaluated. The fidelity of the RAPT operational model is assessed by comparing RAPT departure status with observed departure flows (i.e., trajectories, weather avoidance maneuvers and storm penetrations) on several days when convective weather SWAPs were in effect in New York. Real-time in-situ observations at RAPT facilities (described in a companion paper at this conference; Robinson, 2008), user feedback from RAPT playbacks and the REPEAT web site are used to support this post-event evaluation. For example, real time observations provide the time and operational rationale for a specific departure route closure identified in the traffic flow analysis. This information is necessary to identify closures or flow restrictions that are the result of factors outside of the current RAPT algorithm domain (e.g., traffic restrictions due to volume, downstream congestion, etc.). Real time observations are also used to identify specific times when critical, weather-related operational decisions were made. The RAPT guidance at these critical decision points is analyzed to determine if RAPT provided information that enabled (or could have enabled, had it been used) more timely or effective decisions. The effect of forecast uncertainty on RAPT performance is also examined, particularly in convective weather situations where the location, severity and operational impact were difficult to predict. Strategies that mitigated risks associated with forecast uncertainty are presented. These include the use of additional information provided in the RAPT display, such as echo top heights encountered along the departure route, to confirm or modify RAPT guidance and the consideration of the departure status of two or more adjacent routes to 'average out' variations in the departure status timelines.
Summary
In this paper, the revised RAPT algorithm and display are described and evaluated. The fidelity of the RAPT operational model is assessed by comparing RAPT departure status with observed departure flows (i.e., trajectories, weather avoidance maneuvers and storm penetrations) on several days when convective weather SWAPs were in effect in...
READ MORE
Key research issues for near term operational use of integrated convective weather-ATM decision support systems
January 20, 2008
Conference Paper
Published in:
13th Conf. on Aviation, Range and Aerospace Meteorology, ARAM, 20-24 January 2008.
Topic:
R&D area:
R&D group:
Summary
Thunderstorm-related delays dominate the overall U.S. airspace delay statistics and continue to increase, even though a number of new weather information systems and air traffic management (ATM) decision support tools have been deployed since 1999. Operational decision makers must mitigate the network congestion that arises from rapidly varying capacity loss in both en route and terminal airspace. Improving decision making in such an environment requires explicitly considering airspace structure, network impacts, forecast uncertainty and pilot preferences for weather avoidance. To date, the NextGen initiative has focused on envisioning an operational concept and research agenda for 2025 where it is assumed that aircraft separation and weather avoidance is accomplished using a high degree of automation. In this paper, we consider research to achieve significant improvements in the near term (2010-2015) where aircraft separation is provided largely by controllers and hazardous weather avoidance is accomplished by pilots using visual cues, reports from other aircraft, on board weather radar and ATC advisories. We briefly review the current status of work in key areas and then suggest major near term initiatives. Key elements of the research program to be discussed include: 1. Translation of convective weather products into ATC impacts (including handling of uncertainty in the convective weather forecasts). Initial models for en route pilot avoidance of storms and sector capacity in convective weather have shown promising results, but clearly much more research is needed in this area. 2. Determining when and where available capacity was not appropriately utilized during convective events, based on both facility observations during storm events and computations of avoidable delay. Preliminary results suggest that much of today's delay is in fact avoidable. 3. Developing integrated weather-ATM decision support tools (DST) to enable decision makers to more fully utilize available capacity. The accuracy of contemporary convective weather forecasts is a key issue in the design of such systems. Initial operational experience with a departure decision support tool will be discussed to illustrate key points. 4. Explicitly considering the human side of convective weather ATM [e.g., how individuals make real time decisions in collaboration with other decision makers (e.g., ATC, airlines, dispatch, pilots)]. Recent results from field usage of convective weather decision support tools will be interpreted in the context of recent literature on how people actually make decisions and perform cognitively complex functions in demanding situations.
Summary
Thunderstorm-related delays dominate the overall U.S. airspace delay statistics and continue to increase, even though a number of new weather information systems and air traffic management (ATM) decision support tools have been deployed since 1999. Operational decision makers must mitigate the network congestion that arises from rapidly varying capacity loss...
READ MORE
Improving weather radar data quality for aviation weather needs
January 20, 2008
Conference Paper
Published in:
13th Conf. on Aviation, Range and Aerospace Meteorology, ARAM, 20-24 January 2008.
Topic:
R&D area:
R&D group:
Summary
A fundamental function of any aviation weather system is to provide accurate and timely weather information tailored to the specific air traffic situations for which a system is designed. Weather location and intensity are of prime importance to such systems. Knowledge of the weather provides "nowcasting" functionality in the terminal and en route air spaces. It also is used as input into aviation weather forecasting applications for purposes such as storm tracking, storm growth and decay trends, and convective initiation. Weather radar products are the primary source of the weather location and intensity information used by the aviation weather systems. In the United States, the primary radar sources are the Terminal Doppler Weather Radar (TDWR) and the Weather Surveillance Radar 1988 Doppler (WSR-88D, known as NEXRAD). Additional weather radar products from the Canadian network are used by some of the aviation weather systems. Product quality from all these radars directly impacts the quality of the down stream products created by the aviation weather systems and their utility to air traffic controllers. Four FAA weather systems use some combination of products from the aforementioned radars. They are the Corridor Integrated Weather System (CIWS), the Integrated Terminal Weather System (ITWS), the Weather and Radar Processor (WARP), and the Medium Intensity Airport Weather System (MIAWS). This paper focuses on the improvement of weather radar data quality specific to CIWS. The other mentioned FAA aviation weather systems also benefit either directly or indirectly from the improvements noted in this paper. For CIWS, the legacy data quality practices involve two steps. Step one is the creation of weather radar products of highest possible fidelity. The second step involves creating a mosaic from these products. The mosaic creation process takes advantage of inter-radar product comparisons to interject a further level of improved data quality. The new CIWS data quality plan will use a mounting evidence data quality classifier technique currently being developed. The technique applies a multi-tiered approach to weather radar data quality. Its premise is that no single data quality improvement technique is as effective as a collaboration of many. The evidence will be expanded to include data and products from the radars along with data from additional sensing platforms. The mosaic creation process will correspondingly expand to take advantage of the additional evidence. Section 2 covers data quality of products from the single radar perspective. Section 3 focuses on the use of satellite data as the first additional sensing platform to augment removal of problematic radar contamination. Section 4 describes the data quality procedures associated with creation of mosaics from the single radar products augmented with new satellite masking information. Last, Section 5 discusses future plans for the mounting evidence data quality improvement technique.
Summary
A fundamental function of any aviation weather system is to provide accurate and timely weather information tailored to the specific air traffic situations for which a system is designed. Weather location and intensity are of prime importance to such systems. Knowledge of the weather provides "nowcasting" functionality in the terminal...
READ MORE
Measuring the utilization of available aviation system capacity in convective weather
January 20, 2008
Conference Paper
Published in:
13th Conf. on Aviation, Range and Aerospace Meteorology, ARAM, 20-24 January 2008.
Topic:
R&D area:
R&D group:
Summary
There is currently great interest in improving the ability to quantitatively assess how well U.S. Air Traffic Control (ATC) services are being provided as new weather-air traffic management (ATM) decision support capabilities are added. One of the three proposed metrics currently under study by the Federal Aviation Administration (FAA) and airlines is resource utilization, which has been defined as "the safe and efficient use of available airport or airspace capacity." Measurement of capacity utilization is particularly difficult during convective weather since storms cause capacity reductions in both en route and terminal airspace. In particular, en route capacity loss results in network congestion that cannot be readily characterized by scalar metrics. This paper proposes the use of (i) models for translating 3-D weather radar data into time-varying estimates of the capacity reductions in affected en route sectors, terminal airspace, and airports, together with (ii) automatically-generated, broad-area ATM strategies that utilize the time-varying estimates of airspace capacity and demand to determine optimal reroute strategies or, when necessary, minimally disruptive ground or airborne delay programs to assess how the available capacity could best been utilized. By comparing actual vs. optimal capacity utilization, one can assess how effective the actual weather-ATM system was at utilizing the available capacity. Examples of applying this methodology to severe convective weather events from 2005 and 2006 will be presented.
Summary
There is currently great interest in improving the ability to quantitatively assess how well U.S. Air Traffic Control (ATC) services are being provided as new weather-air traffic management (ATM) decision support capabilities are added. One of the three proposed metrics currently under study by the Federal Aviation Administration (FAA) and...
READ MORE
Spectral representations of nonmodal phonation
January 1, 2008
Journal Article
Published in:
IEEE Trans. Audio, Speech, Language Proc., Vol. 16, No. 1, January 2008, pp. 34-46.
Topic:
R&D area:
Summary
Regions of nonmodal phonation, which exhibit deviations from uniform glottal-pulse periods and amplitudes, occur often in speech and convey information about linguistic content, speaker identity, and vocal health. Some aspects of these deviations are random, including small perturbations, known as jitter and shimmer, as well as more significant aperiodicities. Other aspects are deterministic, including repeating patterns of fluctuations such as diplophonia and triplophonia. These deviations are often the source of misinterpretation of the spectrum. In this paper, we introduce a general signal-processing framework for interpreting the effects of both stochastic and deterministic aspects of nonmodality on the short-time spectrum. As an example, we show that the spectrum is sensitive to even small perturbations in the timing and amplitudes of glottal pulses. In addition, we illustrate important characteristics that can arise in the spectrum, including apparent shifting of the harmonics and the appearance of multiple pitches. For stochastic perturbations, we arrive at a formulation of the power-spectral density as the sum of a low-pass line spectrum and a high-pass noise floor. Our findings are relevant to a number of speech-processing areas including linear-prediction analysis, sinusoidal analysis-synthesis, spectrally derived features, and the analysis of disordered voices.
Summary
Regions of nonmodal phonation, which exhibit deviations from uniform glottal-pulse periods and amplitudes, occur often in speech and convey information about linguistic content, speaker identity, and vocal health. Some aspects of these deviations are random, including small perturbations, known as jitter and shimmer, as well as more significant aperiodicities. Other...
READ MORE
Performance metrics and software architecture
January 1, 2008
Book Chapter
Published in:
High Performance Embedded Computing Handbook, Chapter 15
Topic:
R&D area:
R&D group:
Summary
This chapter presents that high performance embedded computing (HPEC) software architectures and evaluation metrics. A canonical HPEC application is used to illustrate basic concepts. The chapter discusses different types of parallelism are reviewed, and performance analysis techniques. It presents a typical programmable multicomputer and explores the performance trade-offs of different parallel mappings on this computer using key system performance metrics. HPEC systems are amongst the most challenging systems in the world to build. Synthetic Aperture Radar (SAR) is one of the most common modes in a radar system and one of the most computationally stressing to implement. Often the first step in the development of a system is to produce a rough estimate of how many processors will be needed. The parallel opportunities at each stage of the calculation discussed in the previous section show that there are many different ways to exploit parallelism in this application. The chapter concludes with a discussion of the impact of different software implementations approaches.
Summary
This chapter presents that high performance embedded computing (HPEC) software architectures and evaluation metrics. A canonical HPEC application is used to illustrate basic concepts. The chapter discusses different types of parallelism are reviewed, and performance analysis techniques. It presents a typical programmable multicomputer and explores the performance trade-offs of different...
READ MORE
Radar Signal Processing: An Example of High Performance Embedded Computing
January 1, 2008
Book Chapter
Published in:
High Performance Embedded Computing Handbook, Chapter 6
Topic:
R&D area:
R&D group:
Summary
This chapter focuses on the computational complexity of the front-end of the surface moving-target indication (SMTI) radar application. SMTI radars can require over one trillion operations per second of computation for wideband systems. The adaptive beamforming performed in SMTI radars is one of the major computational complexity drivers. The goal of the SMTI radar is to process the received signals to detect targets while rejecting clutter returns and noise. The radar must also mitigate interference from unintentional sources such as RF systems transmitting in the same band and from jammers that may be intentionally trying to mask targets. The pulse compression stage filters the data to concentrate the signal energy of a relatively long transmitted radar pulse into a short pulse response. The relative range rate between the radar and the ground along the line of sight of the sidelobe may be the same as range rate of the target detected in the mainbeam.
Summary
This chapter focuses on the computational complexity of the front-end of the surface moving-target indication (SMTI) radar application. SMTI radars can require over one trillion operations per second of computation for wideband systems. The adaptive beamforming performed in SMTI radars is one of the major computational complexity drivers. The goal...
READ MORE